Aquaponics germination stationOn 3 September 2018 in Agro
In this post I’m going to go through the process of building my aquaponics germination station, materials used and shop where I got them from.
I bought this rack from DC Rack at Jalan Green. They have variety of racks at reasonable price, so it’s highly recommended.
Ball valve is extremely important here to control the water flow. I have to match the flow rate of water that coming into the grow bed, which is under pressure, with the flow rate of water that coming out, which is by gravity. If the water coming in is more than the water that coming out, the grow bed may be flooded and water level in aquarium may dry out.
On the other hand, the outlet pipe should be clear of any debris as it might slow down the water flow, which again may cause the grow bed to flood, as it only depends on gravity.
All of the 16mm elbow, tee and connector I use here were bought from Garden Hobbies Collection near Emart Matang, while the tank connector I got from SK Hardware, and the pipe was ordered online, but it also can be bought from the gardening store mentioned earlier.
I bought these grow light online, and for those who plan to buy them, make sure it matches your electricity voltage and current type. This grow light supports 85-265V AC (alternate current), and here we have 240V, so it matches. If the product stated DC (direct current), it only support electricity from batteries or solar panel, or you need to use adapter (to convert AC to DC) if you want to connect with your home electricity system.
This LED grow light emits blue and red colour lights, essential lightwave for plants to perform photosynthesis. Alternative to this, is by using regular light bulb, but by mixing the cool day light and warm light, to provide the full light spectrum needed by plants.
Aerator is needed in this setup to provide extra dissolved oxygen, not only for the fish but also for the water that get pumped up to the grow bed, to prevent root rot. There’s also another LED light above the aquarium, which we turn on only at night, and it provides nice view of the fishes inside the aquarium.
Another method is using cocopeat – spray it with water to wet it a bit, then fill it into the germination tray with larger hole, poke a tiny hole at the cocopeat then put seeds in there. This method is more suitable to larger type of plants, which take longer time to germinate & have larger root system.
We cover the grow bed area with cloth because the glare from the grow light is unpleasant to our eyes, and since this germination station located in the living room, we’ll see it often as we pass by and we want to reduce this disturbance. This cloth also need to be held together using paper clip because when there’s wind coming in, the cloth might flapping around and land on the grow bed or in the water.
I don’t have the full test kit, so I can’t verify if the system is already cycled – by checking for presence of nitrite and nitrate. It’s already been around more than two weeks, based on online reference, it may take up to 2 months for the system to be fully cycled.
So far, the routine we have done is to feed the fish 3 to 4 times daily, each time with a pinch of feed. And every day I’ll take the ammonia level reading, and if the level stays at 2.0 ppm for two days, then on the third day I’ll do a water change. Note also that I use harvested rainwater for the water inside this system. Other than that, we don’t have to worry much about the plants as they grow by itself with enough light, water and nutrient.
- Cara membuat sistem NFT untuk akuaponik – Saluran tanaman (channel)
- 3 Jenis Asas Sistem Hidroponik Yang Digunakan Dalam Akuaponik Serta Variasinya
- Video tinjauan set aquaponics
- Aquaponics update sebelum tahun baru
- Pindah ikan dalam tangki aquaponics
- Cara membuat sistem NFT untuk akuaponik – Sambungan kembali ke tangki takungan
- Install water pump and test run
- Installing DWC unit
- Scaling down aquaponics set
- Aquaponics build materials & water test kits